Home / Tag Archives: intools course in hyderabad

Tag Archives: intools course in hyderabad

About the CAESAR II Documentation

Caesar-II-Documentation

To address the sheer volume of information available on CAESAR II and present it in a concise and useful manner to the analyst the program documentation is presented in three separate manuals: The User Guide describes the basic operation and flow of the many routines found in CAESAR II. This document provides necessary installation information, gives an overview of the ... Read More »

Flexibility Analysis

Flexibility Analysis

Stress Analysis Criteria: This stress analysis criteria establishes the procedure, lists critical lines and piping stress/design liaison flow sheet to be followed. Lines to be analyzed: all lines attached to pumps, compressors, turbines and other rotating equipment all lines attached to reciprocating compressors all pressure relief valve piping all category m piping Related Courses in Engineering Design ASNT NDT Training ... Read More »

Control Valve (Handled by Instrumentation Department)

oilandgasclub.com-piping -design-course-in-chennai

These valves are self operated type. They have actuators. Actuators operate on the signal received from an instrument. They are used for very fine throttling and to have desired process parameters (pressure, temperature, flow) of fluid. Control valves can be of the following types based on parameters to be controlled: 1) Pressure control valve – Receives signal from pressure indicator ... Read More »

Process Flow Diagram Symbols – Valves

Piping codes and standards

Gate valve is a device used to control the flow of liquids and gases. Check valve also known as one-way valve, is to prevent the line of medium back. Globe valve is a mechanism used to control or stop the flow of liquid or gas through a pipe. Ball valve is a valve with a spherical disc, the part of ... Read More »

Question Related to Post Weld Heat Treatment

post weld heat treatment

1.What is mean by  ‘PWHT’ why is required ? “POST WELD HEAT TREATMENT” this is done to remove residual stress left in the joint which may cause brittle fracture 2.Why pre-heating is done on some pipe before starting welding? To slow down the cooling rate 3.Why post –heating is done on some pipe after the welding is over ? To ... Read More »

Questions for RTR Piping

Stress questions

1.What is the maximum time limit to test backfilled portion? 24 Hr 2.For the line whose joints have not been backfilled what is the maximum time limit for testing ? 04 Hrs 3.a)What is the minimum number of gauge to be used in pressure testing ? Two b) What should be its ranger as per ASME .sec VIII As per ... Read More »

Questions Related to Structural Steel

oilandgasclub.com coating insulation cathodic protection

1. Describe the steps used for erection of structural steel? Material received at site Concrete bases and anchor bolts Shims Pre assembly at ground level Main construction steel erection (dimension bolt) Tightening for anchor bolt Alignment for structural steel Tightening for steel Tightening for anchor bolts. Grouting Complete structural steel erection (secondary beams, bracing) Calibration of whrench and device Modification ... Read More »

Questions Related to Plumbing

oilandgasclub.com plumbing

1.What is the discharge pipe that is flow condition and that extends from the lift station carrying sewage under pressure ? Force main 2 .Where will the drain from battery rooms battery rooms  before discharge to the sanitary sewer line ? Neutralization Tan 3.What is the minimum size of sewer lines that are allowed to be embedded  unde slab? 64mm ... Read More »

Job Oriented Training for Working Persons and Fresher Engineers Oil & Gas, Power Plant

ong course

Dear Engineer, OilAndGasClub.com – Your Career Partner Now @ Chennai Oilandgasclub.com, Chennai offers Job Oriented EPC Training programs for working persons and fresher engineers. Oil And Gas Club is an international Oil and Gas and conference and training organization. O&G club provide Engineering Design Training for onshore & offshore industries. The Faculties are qualified and well experienced professionals who have ... Read More »

Isometric for Pump Discharge Line & Suction Line

isometrtic

Isometric for Pump discharge Line Isometric view for the below Pump suction line Top Courses in Engineering Design PDMS Training 3+ Live Projects 700+ Interview Questions 24/7 E-learning Access SP3D Training Certified Trainer 700+ Interview Questions Job Assistance PDS Training 40+ Mock test 20+ Sub Topic Job Assistance Intools Training 3+ Live Project 20+ Sub Topic Expert Mentors Tekla Training ... Read More »

Free WordPress Themes - Download High-quality Templates