Home / Tag Archives: piping engineering course in chennai

Tag Archives: piping engineering course in chennai

Dynamic Simulation in Chemical Engineering

Dynamic-Simulation-in-Chemical-Engineering

Dynamic simulation is an extension of steady-state process simulation whereby time-dependence is built into the models via derivative terms i.e. accumulation of mass and energy. The advent of dynamic simulation means that the time-dependent description and control of real processes in real or simulated time are possible. This includes the description of starting up and shutting down a plant, changes ... Read More »

Placing Dead Weight Support

Placing-Dead-Weight-Support

This tip will give you a guideline for locating the supports in your piping system Locate dead weight supports using recommended spacing from the code (B31 etc.). Consider existing support points. Decrease span by half off equipment. Decrease span for concentrated loads. Support concentrated loads. Support offset loads. Decrease span for extra lagging or insulation. Locate supports at changes in ... Read More »

What is Oil Refinery ?

what-is-oil-refinery

When talking about refinery, we need to be able to differentiate and identify an oil refinery from the edible oil refinery. Basically, the oil refinery (or petroleum refinery) is an industrial process plant where crude oil (from crude petroleum) is processed and refined into more useful petroleum products, such as Gasoline Diesel fuel Asphalt base Heating oil Kerosene Liquefied petroleum ... Read More »

What do Petroleum Engineers do?

what-do-petroleum-engineers-do

Petroleum Engineers are employed by oil or gas companies to design, test and implement efficient methods to extract petroleum products from the earth and sea floor. They spend most of their time making estimations because they can never see what is actually going on thousands of meters below the ground. They work closely with other professionals, such as geologists, to ... Read More »

Flexibility Analysis

Flexibility Analysis

Stress Analysis Criteria: This stress analysis criteria establishes the procedure, lists critical lines and piping stress/design liaison flow sheet to be followed. Lines to be analyzed: all lines attached to pumps, compressors, turbines and other rotating equipment all lines attached to reciprocating compressors all pressure relief valve piping all category m piping Related Courses in Engineering Design ASNT NDT Training ... Read More »

Responsibilities of Piping Construction Engineers

Responsibilities of Piping Construction Engineers

A piping construction engineer plans the schedule of piping works, assists with material procurement, oversees installations and maintenance operations and supervises construction staff. To become one, you typically need to earn a bachelor’s degree in mechanical, structural or civil engineering, fulfill licensing requirements and have excellent teamwork, decision-making and communication skills. A piping construction engineer often reports to a construction ... Read More »

Role of the Pipe Field Engineer in Safety

ROLE OF THE PIPE FIELD ENGINEER IN SAFETY

The Piping or Mechanical Field Engineer is a direct contributor to the safety of the work operations at the construction site. Since all safe work operations must begin with pre-planning, the Field Engineer makes a direct contribution to safety by reviewing the planned work with safety in mind. The Field Engineer is typically responsible to develop a detailed work package ... Read More »

Code Design Temperature & Design Pressure

code design temperature & design pressure

Code Design Temperature & Design Pressure Pressure Design Temperature Design Pressure B31.1 The piping shall be designed for a metal temperature representing the maximum sustained condition expected. The design temperature shall be assumed to be the same as the fluid temperature unless calculations or tests support the use of other data, in which case the design temperature shall not be ... Read More »

Piping Design Engineer Interview Questions Part-13

piping design engineer interview questions part 13

1. What is the ASME code followed for design of piping systems in process piping (refineries&chemical industries)? A) B31.1 B)B31.3 C)B31.5 D)B31.9 Ans: (B) 2. What do you mean by following items? A)ISLB-400 B)ISMB-600 C)ISHB-350 D)ISMC-300 E)ISJB-150 F)ISLB-200 G)ISMB-450 H)ISWB-400 I)ISJC-200 J)ISLC-350 K)ISMC-250 Ans: A – Indian STD lightweight beam, web size-400 B – Indian STD medium weight beam, web ... Read More »

About Globe Valves

About Global Valves

Overview: A Globe valves is a linear motion valve and are primarily designed to stop, start and regulate flow. The disk of a Globe valve can be totally removed from the flow-path or it can completely close the flow-path. Conventional Globe valves may be used for isolation and throttling services. Although these valves exhibit slightly higher pressure drops than straight=through ... Read More »

Free WordPress Themes - Download High-quality Templates