Home / Tag Archives: pdms course training institute t nagar chennai chennai tamil nadu (page 5)

Tag Archives: pdms course training institute t nagar chennai chennai tamil nadu

Piping Design Engineer Interview Questions Part-11 (Valves – V)

Piping Design Engineer Interview Questions Part-11

41. What is relief valve? Valve to relieve excess pressure in liquids in situations where full flow discharge is not required, when release of small volume of liquid would rapidly lower pressure. 42. What is safety valve? Rapid opening(popping action) full flow valve for air and other gases. 43. What is foot valve? Valve used to maintain a head of ... Read More »

Safety Questionaire

Nebosh training in kerala

1. Name seven places of safety equipment that a fabricator will use? Helmet Head protection Goggles, cutting googles Eye protection Ear plugs Ear protection Grinding Shield Face protection Leather gloves Hand protection Fire proof coveralls Body protection Safety shoes Leg protection 2. How should oxygen & acetylene cylinders be stored when in use? Secured with a cap and chain Upright ... Read More »

ASTM Materials

piping engineering training

Pipes A106 = This specification covers carbon steel pipe for high-temperature service. A335 = This specification covers seamless ferritic alloy-steel pipe for high-temperature service. A333 = This specification covers wall seamless and welded carbon and alloy steel pipe intended for use at low temperatures. A312 = Standard specification for seamless, straight-seam welded, and cold worked welded austenitic stainless steel pipe ... Read More »

Piping Design Engineer Interview Questions Part-9 (Valves-III)

Piping Design Engineer Interview Questions Part-9

21. Where stop check valve is used? In stem generation by multiple boilers, where a valve is inserted between each boiler and the main steam header. It can be optionally closed automatically or normally. 22. Where diaphragm valves are used? Used for low pressure corrosive services as shut off valves. 23. What is barstock valve? Any valve having a body ... Read More »

Piping Design Engineer Interview Questions Part-8 (Valves-II)

Piping Design Engineer Interview Questions Part-8

11. What is wire drawing? This term is used to indicate the premature erosion of the valve seat caused by excessive velocity between seat and seat disc, when valve is not closed tightly 12. What is straight through valve? Valve in which the closing operation of valve is achieved by 90 degrees turn of the closing element. 13. What pressure ... Read More »

Piping Design Engineer Interview Questions Part-7 (Valves-I)

Piping Design Engineer Interview Questions Part 7

1. What are the steps in selection of valve? What to handle, liquid, gas or powder, fluid nature, function, construction material, disc type, stem type, how to operate, bonnet type, body ends, delivery time, cost, warranty. 2. What are functions of valves? Isolation, regulation, non-return and special purposes. 3. What are isolating valves? Gate, ball, plug, piston, diaphragm, butterfly, pinch. ... Read More »

Piping Design Engineer Interview Questions Part-6 (Drums)

piping design course in noida

15. What are drum internals? Demister pads, baffles, vortex breakers, distribution piping. 16. What are drum elevation requirements? NPSH, minimum clearance, common platforming, maintenance, operator access. 17. What are drum supports? Skirt for large drums, legs, lugs, saddles for horizontal drums. 18. What are necessary nozzles for non-pressure vessel? Inlet, outlet, vent, manhole, drain, overflow, agitator, temperature element, level instrument, ... Read More »

Piping Design Engineer Interview Questions Part-5 (Compressors)

piping engineering

1.What are the types of compressors? Positive displacement, centrifugal and axial, rotary screw, rotary vane, rotary lobe, dynamic, liquid ring compressors. 2.What are the types of compressor drives? Electric motor, gas turbine, steam turbine and gas engine. 3.How centrifugal compressors work? High speed impellers increase the kinetic energy of the gas, converting this energy into higher pressures in a divergent ... Read More »

Flanges and types of flanges

Flanges and types

A flange is a method of connecting pipes, valves, pumps and other equipment to form a piping system. It also provides easy access for cleaning, inspection or modification. Flanges are usually welded or screwed. Flanged joints are made by bolting together two flanges with a gasket between them to provide a seal. Types of Flanges The most used flange types ... Read More »

Free WordPress Themes - Download High-quality Templates