Home / Tag Archives: PDMS Course in Mumbai

Tag Archives: PDMS Course in Mumbai

Dynamic Simulation in Chemical Engineering

Dynamic-Simulation-in-Chemical-Engineering

Dynamic simulation is an extension of steady-state process simulation whereby time-dependence is built into the models via derivative terms i.e. accumulation of mass and energy. The advent of dynamic simulation means that the time-dependent description and control of real processes in real or simulated time are possible. This includes the description of starting up and shutting down a plant, changes ... Read More »

ASTM / American Society for Testing and Materials

ASTM-American-Society-for-Testing-and-Materials

There are numerous American Society for Testing and Materials designations cover the specification of wrought materials, forgings and castings used for plate, fittings, pipe and valves.The ASTM standards are directed to dimensional standards, materials and strength considerations. Some of the more material standards referenced are: A 36 Specification for Structural Steel A 53 Specification for Pipe, Steel, Black and Hot ... Read More »

ASME B16 Piping Component Standards

ASME-B16-Piping-Component-Standards

Piping component standard developed by the American Society of Mechanical Engineers or the American National Standards Institute (ANSI) B16.1 Cast Iron Pipe Flanges and Flanged Fittings B16.3 Malleable Iron Threaded Fittings, Class 150 and 300 B16.4 Cast Iron Threaded Fittings, Classes 125 and 250 B16.5 Pipe Flanges and Flanged Fittings B16.9 Factory Made Wrought Steel Buttwelding Fittings B16.10 Face to ... Read More »

Process Flow Diagram Symbols – Valves

Piping codes and standards

Gate valve is a device used to control the flow of liquids and gases. Check valve also known as one-way valve, is to prevent the line of medium back. Globe valve is a mechanism used to control or stop the flow of liquid or gas through a pipe. Ball valve is a valve with a spherical disc, the part of ... Read More »

Question Related to Post Weld Heat Treatment

post weld heat treatment

1.What is mean by  ‘PWHT’ why is required ? “POST WELD HEAT TREATMENT” this is done to remove residual stress left in the joint which may cause brittle fracture 2.Why pre-heating is done on some pipe before starting welding? To slow down the cooling rate 3.Why post –heating is done on some pipe after the welding is over ? To ... Read More »

Questions for RTR Piping

Stress questions

1.What is the maximum time limit to test backfilled portion? 24 Hr 2.For the line whose joints have not been backfilled what is the maximum time limit for testing ? 04 Hrs 3.a)What is the minimum number of gauge to be used in pressure testing ? Two b) What should be its ranger as per ASME .sec VIII As per ... Read More »

Questions Related to Structural Steel

oilandgasclub.com coating insulation cathodic protection

1. Describe the steps used for erection of structural steel? Material received at site Concrete bases and anchor bolts Shims Pre assembly at ground level Main construction steel erection (dimension bolt) Tightening for anchor bolt Alignment for structural steel Tightening for steel Tightening for anchor bolts. Grouting Complete structural steel erection (secondary beams, bracing) Calibration of whrench and device Modification ... Read More »

Questions Related to Plumbing

oilandgasclub.com plumbing

1.What is the discharge pipe that is flow condition and that extends from the lift station carrying sewage under pressure ? Force main 2 .Where will the drain from battery rooms battery rooms  before discharge to the sanitary sewer line ? Neutralization Tan 3.What is the minimum size of sewer lines that are allowed to be embedded  unde slab? 64mm ... Read More »

Job Oriented Training for Working Persons and Fresher Engineers Oil & Gas, Power Plant

ong course

Dear Engineer, OilAndGasClub.com – Your Career Partner Now @ Chennai Oilandgasclub.com, Chennai offers Job Oriented EPC Training programs for working persons and fresher engineers. Oil And Gas Club is an international Oil and Gas and conference and training organization. O&G club provide Engineering Design Training for onshore & offshore industries. The Faculties are qualified and well experienced professionals who have ... Read More »

Isometric for Pump Discharge Line & Suction Line

isometrtic

Isometric for Pump discharge Line Isometric view for the below Pump suction line Top Courses in Engineering Design PDMS Training 3+ Live Projects 700+ Interview Questions 24/7 E-learning Access SP3D Training Certified Trainer 700+ Interview Questions Job Assistance PDS Training 40+ Mock test 20+ Sub Topic Job Assistance Intools Training 3+ Live Project 20+ Sub Topic Expert Mentors Tekla Training ... Read More »

Free WordPress Themes - Download High-quality Templates