Home / Blog / Piping Design Engineer Interview Questions:- Part-2

Piping Design Engineer Interview Questions:- Part-2

piping-design-interview-questions


51. What is regular pattern plug valve?
Rectangular port, area almost equal to pipe bore, smooth transition from round body to rectangular port, for minimum pressure loss.
52. What are short pattern plug valve?
Valves with face to face dimension of gate valve, as a alternative to gate valve.
53. What are ventury pattern plug valve?
Change of section through the body throat so graded to have ventury effect, minimum pressure loss.
54. What are inverted plug design valve?
Plug valve with taper portion up of plug. For 8” and higher size.
55. What is pressure balanced plug valve?
With holes in port top and bottom connecting two chambers on top and bottom of plug, to reduce turning effort.
56. What are teflon sleeved plug valve?
PTFE sleeve between plug and body of valve, low turning effort, minimum friction, temperature limitation, anti static design possible.
57. What are permasil plug valve?
Plug valves with teflon seat instead of sleeves, for on off applications, can handle clean viscous and corrosive liqiuids, graphite seat for high temperature applications. Drip tight shut off not possible.
58. What are eccentric plug valve?
Off center plug, corrosive and abrasive service, on off action, moves into and away from seat eliminating abrasive wear.
59. What is dimensional standard for plug valve?
API 599.
60. What is pinch valve?
Similar to diaphragm valve, with sleeves of rubber or PTFE, which get sqeezed to control or stop the flow, cast iron body, for very low service pressures like isolation of hose connections, manufacture standard.
61. What is needle valve?
Full pyramid disc, same design as globe valve, smaller sizes, sw or threaded, flow control, disc can be integral with stem, inside screw, borged or barstock body and bonnet, manufacturers standard.
62. How to install a globe valve ?
Globe valve should be installed such that the flow is from the underside of the disk, Usually flow direction is marked on the globe valve.
63. What are globe valve port types?
Full port: More than 85% of bore size, Reducer port: One size less than the connected pipe.
64. What are globe valve disk types?
Flat faced type for positive shutoff, loose plug type for plug renewal or needle type for finer control.
65. What are characteristics of globe valve stem?
Always rising design, with disk nut at the lower end and handwheel at upper end.
66. What are types of globe valve?
Angle globe valve, plug type disc globe valve, wye-body globe valve, composite disc globe valve, double disc globe valve.
67. What is angle globe valve?
Ends at 90 degree to save elbow, higher pressure drop.
68. Where plug type disc globe valve is used?
For severe regulating service with gritty liquids such as boiler feedwater and for blow off service.
69. Where WYE body globe valve is used ?
In line ports with stem emerging at 45 degree, for erosive fluids due to smoother flow pattern.
70. What is double disc globe valve ?
Has two discs bearing on separate seats spaced apart, on a single shaft, for low torque, used for control valves.
71. What are port types for gate valves?
Full port and reduced port. Default is reduced bore. Full port has to be specified in bom.
72. How to close a gate valve ?
Turn the handwheel in clockwise direction.
73. What is lantern ring?
It’s a collection point to drain off any hazardous seepages or as a point where lubricant can be injected, it is in the middle of packing rings.
74. What are types of gate valves?
Solid plane wedge, solid flexible wedge, split wedge, double disc paralles seats, double disc wedge, single disc single seat gate or slide, single disc parallel seats, plug gate valve.
75. What are the types of bonnets?
Bolted bonnet, bellow sealed bonnet, screwed on bonnet, union bonnets, A U-bolt and clamp type bonnet, breechlock bonnet, pressure seal bonnet.

About Oilandgasclub.com

About Oilandgasclub

Oilandgasclub.com is an international oil and gas (online & offline) conference technical training org from India. Oilandgasclub.com 3000+ professionals trained 150,000 hours of classes delivered 500+ expert trainers available and 3600+ respondents 30+ countries 80+ team. Blogs about technical tips at this blog. Contact or more about customized technical training from this page

70+ courses    7 venues    5 categories

OILANDGASCLUB.COM HAS PUBLISHED 150+ ARTICLES IN THIS BLOG Subscribe

Subscribe to Our Newsletter

More From OilandGasClub

Author

Promoted Articles

Comments (0)

avatar
500

wpDiscuz
+91 8122087919
[sg_popup id=4]Pipeline Integrity Management [/sg_popup]

REQUEST FOR A CUSTOM QUOTE

Please fill in the details and our inhouse support team will get back to you within 1 business day

Name*
Email*
Phone*
Course*
Source*
Company
Looking for
 Online training Class room training
Your Query*

REQUEST FOR A CALL BACK

Have any query about our training, we are here to help

Name*

Email*

Phone*

Course*

Source*

What time suits you?*
 Between 10AM to 1PM IST Between 1PM to 4PM IST Between 4PM to 6PM IST Between 6PM to 8PM IST

Drop Your Info Now

Drop Your Info Now

Drop Your Info Now

2017 is holding lots of good fortune. Griper the offer within this year.

Enlist Now

Your Name

Email Id

Phone Number

Message

Upload Resume

Your Name

Email Id

Phone Number

Upload Resume

Subscribe

Your Name*

Your Email*

Your Country*

Subscription to*
 sub-docnews-check Document Control Newsletter Document Control Salary Survey Document Control Tips & Tools Document Control Events & Courses - Europe (incl. UK) Document Control Events & Courses - North America Document Control Events & Courses - Singapore Document Control Events & Courses - Kuala Lumpur Document Control Events & Courses - Australia Document Control Events & Courses - Middle East Document Control Events & Courses - Asia (other countries)

Request for Proposal

Your Name*
Company Name*
Your E-mail*
Your Phone Number*
Course Required*
Period of Interest*
Location of the course (include full address, post code, city, country)*
Number of course participants*
Tuition Language*
Overall level of proficiency of the participants*
Certification Examination*
Training Facility*
Lecturers expenses : accommodation, meals, local transportation, flights from point of origin*
Is there any withholding tax to be planned? (for Companies outside European Union)*
Currency for Billing (Pound Sterling by Default)*
Would you like to receive our free document control newsletters & tools?*
 Yes, please No, thanks
Free WordPress Themes - Download High-quality Templates